The Plastic Wire Heat Sealing Kit is an intensive treatment that reduces volume, eliminates frizz and provides smooth, controlled yarn for up to 3 months. It deeply nourishes and moisturizes the hair as well as giving incredible shine and strengthening the structure, preventing breakage.
The Treatment Mask is an intensive treatment of treatment for damaged or chemical hair. Penetrates the hairs, eliminating porosity and strengthening the hair fiber to prevent hair breakage.
Contains: Yarn Plastic Step 1 Pre-Sealing Shampoo 110ml/3.71fl.oz: Deep cleans the hair and helps open the cuticle facilitating the penetration of the active principles of the treatment.
Yarn Plastic Step 2 Heat Sealing 110ml/3.71fl.oz: With the other products, it promotes the long lasting natural smooth effect on the hair and leaves the hair shiny and frizz-free.
Yarn Plastic Step 3 Sealant Mask 110ml/3.71fl.oz: Promotes maximum hydration of the yarn reducing frizz and accentuating the smooth effect.
Post Sealing Treatment Mask 200ml/6.76fl.oz: Nourishes and moisturizes deeply leaving the hair super soft, light and shiny longer. Also great as part of the maintenance of Plastic Treatment of Yarn.
Action: Treatment consisting of Arginine, Acai Extract and Acetic Acid (ph acid).
Application: Plastic Wire Heat Sealing Kit: 1- Wash your hair with the Pre-Treatment Shampoo, massaging until foamy. Wash twice in case of virgin hair that is very resistant or very dirty. Let it act for 5 minutes and rinse completely. Attention: Do not rub the scalp.
2- Dry the hair in 80% with the dryer and finger aid.
3- Separate the hair into 6 parts (a vertical line separating the hair into two strands - right and left - and 3 horizontal sessions - neck, middle and front from the ears). Secure each session in a bun with a clip.
4- Pour 20 to 40ml of Heat Seal in a container and put on the silicone gloves.
5- Start applying on a strand of the neck with the aid of the brush. Apply two fingers of the root to the base of the wick and pull the product to the ends with the comb. Make sure the product is on all wires.
6- Repeat the procedure with the side lock.
7- With the dryer in the cold jet, dry the two locks 100%. It is important to dry two strands at a time with the cold jet. This prevents smoke formation and prevents the product from evaporating without effect.
8- Repeat the procedure from 5 to 7 on the two central strands of hair one at a time.
9- Finally, repeat the procedure 5 to 7 on the two front strands of hair, drying the strands back. It is important that neither the dryer wind nor the lint with the product come into contact with the face.
10- Time to board! In blonde, damaged or chemical hair the board temperature should not exceed 200 ° C. For normal, virgin or temperature resistant hair it should be at 230 ° C.
11- Divide the hair again into parts using barrettes. Separate a thin linear strand and plank the length (without the tips) of the strand 10 times (200 ° C board) or 7 times (230 ° C board).
12- Prick the ends (without the length) of the hair up to 4 times (200 ° C board) or 2 times (230 ° C board). This way you avoid the artificial smooth effect on the tips.
13- Repeat this process (steps 11 and 12) for all strands of hair. The straight flat iron with respect to leather makes the strands naturally smooth from the root.
14- After plucking all the strands, rinse the hair well.
15- Apply the Restorative Mask on the wires gently massaging the strands. Let it act for 5 minutes and rinse again.
16- Dry the hair with the dryer.
Máscara de Tratamento Pós-Selagem 200ml: Após lavar o cabelo, aplique a Máscara sobre o comprimento e as pontas dos fios e massageie bem. Penteie e deixe agir por 5 minutos. Enxágüe bem com água.
Cabelos naturalmente lisos, sem frizz, mais fortes e reparados com brilho incrível por até 3 meses!